Why do I not have hot water?
May, June and July are the coldest months on the Gold Coast, and no-one wants to start the day with a cold shower in winter. Unluckily for some clients of Whywait Plumbing who are not Service Partners it is in these months they go to the shower and question why do I not have hot water?
Unfortunately, hot water systems are a case of out of sight out of mind. Continually where hot water systems are concerned, there were warning signs that there was a problem. Over the summer months, hot water problems are overlooked as the demand for higher temperature; hot water is not a critical consideration.
Several warning bulletins in Queensland have been issued by the QBCC and Queensland Health advising homeowners that their hot water systems need to be maintained and serviced frequently.
AS/NZS 3500.4:2018 Heated Water Services
The Australian standard that all hot water installation is based around is AS/NZS 3500.4:2018 Heated water services that are an integral part of the National Construction Code of Australia issued by the Australian Building Codes Board and it is all legal requirements in Queensland.
In AS/NZS 3500.4:2018 there is Appendix M which provides guidelines for the operation and maintenance of your hot water system which is below:
This Appendix provides guidelines for the operation and maintenance of a heated water system.
In order to ensure maximum performance and length of operation, water heaters should be inspected periodically.
M3 MAINTENANCE OF HEATED WATER SERVICES
Heated water services should be maintained in accordance with the following:
(a) Water treatment units: Where installed, water treatment units should be inspected periodically to ensure proper operation.
(b) Water vessels and tanks: All vessels and tanks should be inspected and cleaned periodically, and in accordance with any requirements of the regulatory authority.
NOTE: The frequency of periodic cleaning depends upon the quality of the supply water, design, materials of construction and the pipe system. Combinations of materials giving rise to corrosion should be avoided.
(c) Valves: The following valves should be inspected periodically to ensure proper operation:
(i) Temperature/pressure-relief valves.
(ii) Expansion control valves.
(iii) Thermostatic mixing valves.
(iv) Tempering valves.
(v) Other associated valves/devices.
(d) The requirements of AS/NZS 3666.2, where applicable.
Common reasons for why do I not have hot water
Below are listed the most common reasons we attend to clients jobs who call up to as why do I not have hot water? Listed are elementary troubleshooting ideas that you can undertake yourself to resolve or understand why your hot water is cold:
- blown fuse or circuit breaker – replace the fuse or reset the circuit breaker and if it blows again it’s probable there is a fault with your element or thermostat, and you need to call Whywait out to repair
- Energex relay switch failure – this is not the easiest to detect but if you are on off-peak rates and there are no obvious electrical faults or water leaks then its worth a phone call to your energy supplier to check whether the relay switch has failed to activate in your area
- defective relief valve – most relief valves on the side of the HWS only have a life span of around 3-5 years. Still, they can jam open so first check if you see water running from it by pulling the lever up and then easing back down again. If water continues to run then you need to call Whywait out to service the unit
- no water at all – this is when you wake up turn the tap on and cold water flows, but there is no flow from the hot water. Frequently this a failure of the non-return or isolating valve and a quick way to check is to turn the handle on the valve all the way off and then all the way back on. In many cases, the hot water will simply begin to flow again. However, if there is still no flow you need to call Whywait out for repairs
- water fluctuation from hot to cold – there are several reasons for this occurring, but the most common is a faulty tempering valve. There is nothing you can do to solve fluctuation other than call Whywait and read our information on tempering valves
- water leaking from hot water tank – there is only a maximum of 7 possible points on an HWS tank where there are joints that can possibly leak. Only 2 of those are concealed in the housing so if the water is leaking from the tank and its not from the visible water connections you need to call Whywait for service to check the HWS. In all likelihood, if the hot water tank is more than ten years old then its a 50/50 chance you need a new one installed
The above reasons are the most common problems you will experience with why do I not have hot water. As you can see above, there are only a few simple DIY solutions when you have no hot water.
A word of warning though. Please never open up the housing near the bottom of the tank where the electrical connections are as they are all live wires inside there and therefore very, very dangerous.
Whether you have a solar, heat pump, gas or electric hot water system they do need periodic maintenance so for all hot water problems call Whywait Plumbing now on (07) 5580 4311 as we guarantee a same-day rapid response for hot water problems.
Plumbing innovations have always been the norm in the plumbing industry. Innovation is change and is always about better ways of doing the same thing.
When I started my apprenticeship the clearing of a blocked drain started using a plunger and was at least a two-man job using 1m long drainage rods. The rods were screwed together and manually pushed slowly down the drain until we hit the blockage. Clearing drains this way frequently took 3-4 hours.
Plumbing innovations mean that we now clear a blocked drain with state of the art high-pressure jetrodding technology that was unknown 20 years ago.
Innovation is always about change, but at Whywait Plumbing we have always been at the forefront of plumbing innovations. We have always lead change as Gold Coast plumbers from the purchase of our first high-pressure water jetting unit in 1992 or installing vehicle tracking systems or introducing guaranteed upfront pricing in 1999.
What we always considered was developing and improving our way of solving your plumbing problems is now referred to as disruptive innovation. I agree disruptive innovation is the new term in business in the 21st century. But it’s not new it’s just a new way of talking about improving our methods and practices using the latest technology.
Change is the norm, but it just appears to be frantic to an outside observer with online banking, online shopping, online flight bookings and so the list goes on. At least with plumbing, it can’t be done online except for those DIY enthusiasts who believe Google Plumbing has all the answers.
The level of disruption through plumbing innovations has impacted all plumbing installation and maintenance has been significant starting with:
- Increasing use of prefabrication of bathroom and kitchen modules off-site where the plumbing is all undertaken in a factory, transported to the site and connected up to a water and drainage connection.
- Continual advances in sustainability with the advent of low flow toilets, low flow taps, waterless urinals and recirculated hot water.
- Advances in energy efficient products with heat pump hot water units, solar hot water, instant hot water and underfloor heating.
- All of the different materials we now use in the pipework, relining of existing pipework, CCTV cameras to inspect pipes and pipe jointing methods where welding is now obsolete.
- Excavation methods with advanced technologies in hydro excavation and tracking and locating of underground services.
The ongoing changes in technology in the plumbing industry are disruptive if not embraced. I agree that plumbing innovations cause a significant difference in how we undertake to solve plumbing problems and how the plumbers at Whywait work now.
Ultimately plumbing continues to be about protecting the health and safety of the community for now and the future to ensure we have good quality water and sewer systems in our buildings.
Replacing Your Hot Water Service – How Will You Know What’s Right For You?
When replacing your hot water service the most common question asked is what will it cost?
Whilst price is always an important consideration, at Whywait Plumbing believe that there are other equally important factors. This article will help you make an informed decision.
Should The Price of the Replacement Hot Water Service Be The First Consideration?
Besides renovating your home, replacing your hot water service is a major cost. It is often an expense that occurs with very little warning.
Unfortunately, unless you like cold showers, this gives you little time to carefully review available replacement options.
Hot water systems are not all created equal and the choice you make today will be one that lasts for the next ten to fifteen years. With ever-increasing energy costs impacting household budgets, having an efficient and well maintained hot water service has never been more important. A cheap hot water service may cost you a great deal more in ongoing expenses.
With So Many Hot Water Systems On the Market How Do You Know Which One To Choose?
With modern technological advances and the push for energy-efficient heating solutions, it’s no longer a matter of just replacing your hot water system with like for like. So how do you know which hot water service to buy?
Hot water services are available in electric, gas, solar and heat pump models, and all come in a huge range of sizes. Purchasing the right hot water service for your needs is something you should seek advice about from a qualified hot water specialist. With a little help from Whywait’s Hot Water Specialists you will be able to select the system that best suits your situation.
Hot Water Service FAQ’s
Before making any decisions about a hot water service replacement you will need to think about:
- What size is your current hot water service and have you ever run out of hot water with your current hot water system?
- Does your current hot water service operate on an off-peak electricity tariff?
- Are your hot water needs likely to increase, decrease or stay the same over the next five years?
- Do you intend to remain in your current property for at least the next five years?
- What is more important to you the initial up-front installation cost or the ongoing running costs?
- Is the quality of the product and length of warranty a consideration when comparing hot water services?
Once you have answered the above points it will be time to consider the available options.
Perception is reality and nowhere is this truer for us at Whywait Plumbing than when dealing with the issue of hot water temperature and the possibility of a serious hot water burn.
Everyone has a different perception of how hot they want their hot water whether it is for cleaning or sanitation or personal hygiene use.
Recent research in the United States from the Johns Hopkins Bloomberg School of Public Health, confirms hot water heater temperatures are too high.
In Australia, most manufacturers preset the thermostats for hot water heater temperature at 60-65 degrees. This is dangerously high for a significant proportion of homes, presenting a scald hazard particularly for young children and the elderly. This is because literally hot water burns like fire because:
At 60°C, a serious burn can happen in 1 second
At 55°C, a serious burn would take 10 seconds
At 50°C, a serious burn would happen after 5 minutes
It is estimated a serious hot water burn causes an estimated 1,200 hospital admissions and 50 deaths per year. Young children and elderly adults have thinner skin which burns more quickly putting them at increased risk.
In Queensland, it is the law that hot water delivered to bathrooms used primarily for personal hygiene purposes be regulated by use of a tempering valve or a thermostatic mixing valve that does not exceed 50°C. This is due to the fact that in 1995 the laws were changed requiring tempering valves to be installed on:
all new homes having a hot water system installed
replacement or upgrading of an existing hot water system
or when moving an existing hot water system to a new location on the property
However, homes built before 1995 will frequently still have hot water being delivered at 70°C. It is estimated that 37% of homes still have older electric or gas heaters delivering hot water that presents a scald hazard that will cause a serious hot water burn in one second.
Frequently these homes are rental properties. Many landlords and real estate property managers are unaware that recent litigation has placed a ‘deed of care’ onus on them to ensure the safe delivery of hot water in domestic bathrooms used primarily for personal hygiene purpose.
The installation of a tempering valve is an acceptable solution to hot water scald prevention. Delivering hot water at a consistent temperature is difficult without a tempering valve. This is due to the fact that as a hot water tank is depleted through use then replenished and reheated, the water temperature will not be constant throughout the tank.
Despite a perception by many people, a hot water service thermostat is not designed to provide precise estimates of water temperature. Its purpose is to begin heating when the temperature drops below a set level and turn off when it reaches a set level. Without a tempering valve installed it is almost impossible to assess the exact temperature of hot water delivered from a tap.
The advantage of a tempering valve is that guesswork is eliminated as tempering valves are designed to blend hot and cold water to deliver mixed water at a constant temperature and thus reduce the risk of a serious hot water burn.
Unfortunately for plumbers, property managers, homeowners and property investors hot water has increasingly become a legal minefield with the duty of care provisions.
It is for this reason Whywait Plumbing recommend that you install a tempering valve and maintain it compliantly with annual testing.